Is loud or noisy
Most Likely Causes
Dehumidifier Fan Motor
Most common causeappliancepartsprosFirst, manually rotate the fan blade to verify it spins freely without rubbing against the fan housing. If the blade turns easily and has no contact with the housing, use a multimeter to check if the fan motor is receiving power. If the motor is getting power but the fan still does not run, the motor itself is likely faulty and requires replacement. However, if the blade scrapes the housing or does not spin freely, install a new fan blade before testing the motor. This will ensure the blade issue is not mistakenly attributed to a defective motor.
Repair Steps
- 1.Safety Precautions:
- 2.Locate the Fan Motor:
- 3.Gather Necessary Tools and Replacement Parts:
- 4.Access the Fan Motor:
- 5.Disconnect Wiring:
- 6.Remove the Old Motor:
- 7.Prepare the New Fan Motor:
Dehumidifier Blower Wheel
appliancepartsprosManually rotate the blower wheel to check its condition. If the wheel does not turn freely or is scraping against the housing, install a new blower wheel. Also, if the wheel wobbles when spinning, that signals it is not securely attached to the motor shaft. In that case, tighten the wheel if possible or replace it altogether. Lastly, inspect the wheel for any physical damage. If present, replace the damaged blower wheel with a new one.
Repair Steps
- 1.Safety Precautions:
- 2.Locate the Blower Wheel:
- 3.Gather Necessary Tools and Replacement Parts:
- 4.Access the Blower Wheel:
- 5.Disconnect the Old Blower Wheel:
- 6.Remove the Old Blower Wheel:
- 7.Prepare the New Blower Wheel:
- 8.
Dehumidifier Fan Blade
appliancepartsprosManually rotate the fan blade to assess its condition. Make sure the blade spins freely without rubbing against the fan housing. If the blade does not turn easily or scrapes the housing, the blade is faulty and requires replacement. Also, wiggle the fan motor shaft to check if it is loose. If the shaft moves at all, the blade is not securely attached. In that case, first try tightening the set screw. If that does not fix the issue, install a new fan blade.
Repair Steps
- 1.Safety First:
- 2.Access the Fan Compartment:
- 3.Identify the Fan Blade:
- 4.Detach the Old Fan Blade:
- 5.Clean the Area and Prepare for Installation:
- 6.Install the New Fan Blade:
- 7.Reassemble the Fan Compartment:
- 8.
Dehumidifier Compressor
appliancepartsprosDehumidifier compressors typically produce some noise during normal functioning. However, if the compressor emits unusual sounds or excessive loudness, it could signal the compressor is wearing out. Compressors frequently operate for years after deterioration begins, so replacing a noisy compressor is often not cost-effective. Instead, the abnormal sounds are an early indicator of eventual failure. While the compressor remains functional, albeit noisy, replacement is not yet warranted.
Repair Steps
- 1.Unplug the dehumidifier and disconnect the drain hose. Make sure the dehumidifier is powered off and unplugged before servicing. Also disconnect the drain hose so it's out of the way during the repair.
- 2.Remove the front grille. The grille usually pops off or is held in place with screws. Remove it to access the internal components.
- 3.Take out the old compressor. Locate the compressor towards the bottom or back of the dehumidifier. Remove any screws or brackets securing it in place. Unplug the wires connected to it. Carefully maneuver the compressor out.
- 4.Install the new compressor. Position the new compressor in the same spot as the old one. Reconnect the wiring harness to the terminals on the compressor. Secure with any brackets or screws.
- 5.Replace the front grille. Carefully pop the grille back into place or screw it back on. Make sure all internal wires and tubing are tucked inside and not sticking out.