Not heating
Most Likely Causes
Range/Stove/Igniter
Most common causeappliancepartsprosThe igniter is usually the problem when an oven isn't heating. It has two main roles. First, it pulls electrical current through the oven's safety valve to open it. Second, it heats up to glow and light the gas in the oven burner. If the igniter becomes weak, it won't be able to open the safety valve properly. If the valve doesn't open, the oven won't heat up. To check if the igniter is faulty, watch it when the oven is on. If the igniter glows for over 90 seconds without lighting the gas flame, it's probably too weak to open the valve and needs to be replaced. If the igniter doesn't glow at all, use a multimeter to test for electrical continuity. If the igniter lacks continuity, you'll need to replace it.
Repair Steps
- 1.Shut off power. Locate the circuit breaker for the range and shut it off to cut power to the appliance.
Range/Stove/Bake Element
Most common causeappliancepartsprosWhen the bake element works as it should, it turns red hot. If it doesn't turn red, it means the element isn't heating up. Often, you can see physical damage if the heating element has burned out. Look for holes or blisters on the heating element. To check if the bake element has burned out, use a multimeter, which is a tool that tests whether electricity can move through a component. If the bake element doesn't have continuity, meaning electricity can't flow through it, it needs to be replaced.
Repair Steps
- 1.Disconnect power supply - Locate the circuit breaker for the oven and switch it off before starting work. This prevents electric shock.
- 2.Remove oven racks - Take out all racks and accessories to clear the way to the bake element.
- 3.Locate mounting screws - The bake element is held in place by mounting screws accessible from the rear. Remove these screws.
- 4.Disconnect wires - Detach the electrical connectors from the terminals on the ends of the bake element. Make note of wire positions.
- 5.Extract old element - Gently slide out the old bake element, being careful not to damage the ceramic insulation.
Range/Stove/Control Board
Most common causeappliancepartsprosAn oven's control board will often be used to send voltage to the bake and broil elements or the igniters. If the control board is defective, the voltage may not be sent to these components and the oven will not heat. You can inspect the board for signs of damage or a shorted component. You can also use a multimeter to test for voltage reaching the bake or broil elements or igniters after reviewing the appliance's wiring diagram.
Repair Steps
- 1.Shut off power to the range by locating the circuit breaker and shutting it off. This prevents electric shock.
- 2.Remove the control knobs by gently pulling straight up and off of the stems they attach to. Set aside.
- 3.Remove the control panel of the oven by locating mounting screws around the edges and carefully removing them.
- 4.Disconnect the wire connectors attached to the control board by squeezing release tabs and gently pulling wires free.
- 5.Remove mounting screws or other hardware securing the board in place. Lift out the old board.
- 6.
Igniter
28.9% of casesamazon_reviewsHeating Element
10.9% of casesamazon_reviewsSensor
4.7% of casesamazon_reviewsFuse
4.7% of casesamazon_reviewsTimer
3.9% of casesamazon_reviewsHose
3.9% of casesamazon_reviewsValve
3.1% of casesamazon_reviewsControl Board
2.3% of casesamazon_reviewsRange/Stove/Temperature Sensor
appliancepartsprosThe temperature sensor in an oven keeps track of the temperature inside the oven to make sure it's accurate. If the temperature sensor isn't working right, the oven might not heat up at all. You can test the sensor with a multimeter, a tool that measures electrical properties like resistance, called ohms, at a specific temperature. This can help you figure out if the sensor is faulty.
Repair Steps
- 1.Shut off power to the range by flipping the circuit breaker or unplugging the appliance. This ensures safety during repair work.
- 2.Remove the oven control knobs by gently pulling them straight up off of their stems. Set aside.
- 3.Remove the oven control panel by locating the mounting screws around the perimeter and carefully removing them.
- 4.Disconnect the wires attached to the temperature sensor by squeezing locking tabs and pulling wires free. Note positions or take photos for reference.
- 5.Remove any mounting screws or hardware securing the sensor in place inside the oven cavity.
- 6.Carefully withdraw the old sensor. Avoid damaging its wire leads or silicon insulation.
Range/Stove/Bake or Broil Spark Electrode
appliancepartsprosAn oven burner spark electrode is used to light up the gas for the bake and broil burners. This electrode, a device located next to the burner, works like a spark plug. When electricity is supplied, a spark jumps from the tip of the electrode to its shield, lighting the gas. If the electrode is damaged or worn out, the spark might not happen. Look at the electrode assembly closely for cracks in the porcelain housing or damage to the electrode tip. Keep in mind, the range needs a proper ground and the correct incoming voltage for the electrode control to detect a flame once the burner is lit. If the burner turns off after being lit, ensure there's a proper ground and the correct polarity at the wall outlet.
Repair Steps
- 1.Disconnect power to the range at the main circuit breaker.
- 2.Locate the oven spark electrode near the top/back of the oven cavity.
- 3.Twist the wire connector to unfasten it from the electrode terminal.
- 4.Remove mounting screw securing electrode to the back oven panel.
- 5.Gently wiggle electrode straight up and out of the mounting hole.
- 6.Insert replacement electrode through mounting hole in back panel.
Range/Stove/Broil Element
appliancepartsprosExamine the broil element for any holes or blisters. When it's working correctly, the broil element turns red hot. If it doesn't become red, it means the element isn't heating up. If the broil element has burned out, you'll often be able to see the damage. To check if the broil element has burned out, you can use a multimeter, a tool that tests whether electricity can flow through a component. If the broil element doesn't have continuity, meaning electricity can't pass through it, you'll need to replace it.
Repair Steps
- 1.Disconnect power supply to the range at the main circuit breaker for safety.
- 2.Remove broiler/top oven panels by lifting out mounting clips or screws.
- 3.Carefully pull broil element shelf out to fully access element wires.
- 4.Detach wire leads from element by loosening screwdriver terminal screws.
- 5.Slide old broil element out of mounting slots at rear of broiler box.
- 6.Insert replacement element leads first through access hole before sliding into slots.
Range/Stove/Spark Module
appliancepartsprosFor gas ovens that use a spark igniter, a malfunctioning spark module could be the reason the oven isn't heating up. If you don't see a spark close to the bake or broiler burner tube when the oven is on, use a multimeter. This tool can help you figure out if electricity is reaching the spark module. If the module is getting power but the oven isn't heating, the spark module is probably broken and needs to be replaced.
Repair Steps
- 1.Shut off power to the range at the circuit breaker. This prevents electric shock during repair work.
- 2.Locate the spark module under the control panel area, often secured by screws.
- 3.Disconnect any wiring connected to the module by squeezing locking tabs and pulling wires free.
- 4.Remove mounting screws or hardware securing the module in place.
- 5.Detach the old spark module by lifting it away from the mounting location.
- 6.Position the new spark module into the same space, aligning any mounting holes.
- 7.
Range/Stove/Thermal Fuse
appliancepartsprosIf the oven gets overly hot, the thermal fuse acts like a safety switch and cuts off power to the oven. If this fuse has blown, the oven won't heat up. But this doesn't happen often. To check if the thermal fuse is the problem, you can use a multimeter to test if electricity can flow through it, a property called continuity. If the thermal fuse doesn't have continuity, it needs to be replaced. Remember, a blown thermal fuse can't be reset—it must be replaced if it's blown.
Repair Steps
- 1.Disconnect power to oven. Turn off the power to the range at the main circuit breaker.
- 2.Remove control knobs. Detach any temperature or function control knobs.
- 3.Remove control panel. Unfasten retaining screws to lift off the main oven control console.
- 4.Locate thermal fuse. Identify the thermal fuse mounted on the oven's temperature control housing unit.
- 5.Detach wiring leads. Carefully unplug the electrical connections from the old thermal fuse.
- 6.Remove mounting hardware. Use a screwdriver to detach any screws or clips retaining the fuse.
Range/Stove/Control Board
appliancepartsprosThe oven control board uses relays to send electricity to the bake and broil circuits based on the user's settings and feedback from sensors. If the control board is faulty, it might not send electricity to the heating parts. But, this doesn't happen often. Before you replace the control board, first check all the heating parts. If you find that all the heating parts are working correctly, then the control board should be replaced. Testing the control board isn't simple, so if you think it might be faulty, it's best to just replace it.
Repair Steps
- 1.Shut off power to the range by locating the circuit breaker and shutting it off. This prevents electric shock.
- 2.Remove the control knobs by gently pulling straight up and off of the stems they attach to. Set aside.
- 3.Remove the control panel of the oven by locating mounting screws around the edges and carefully removing them.
- 4.Disconnect the wire connectors attached to the control board by squeezing release tabs and gently pulling wires free.
- 5.Remove mounting screws or other hardware securing the board in place. Lift out the old board.
- 6.Install the new control board and attach with original mounting screws or hardware.
Range/Stove/Safety Valve
appliancepartsprosThe gas oven safety valve cooperates with the oven igniter to supply gas to the burner. If the safety valve breaks, the oven won't heat up. But this seldom happens. Before deciding to replace the safety valve, first check all the oven parts that usually break, especially the igniter. If all the other heating parts are working fine, use a multimeter to test if electricity can flow through the safety valve, a property known as continuity. If the safety valve doesn't have continuity, you should replace it.
Repair Steps
- 1.Shut off gas supply at the main shut-off valve behind or under the appliance.
- 2.Disconnect flex gas line from safety valve by loosening coupling nut with a wrench.
- 3.Remove mounting screws or nuts securing safety valve to appliance structure.
- 4.Gently remove old valve taking care not to scratch nearby surfaces.
- 5.Apply pipe thread sealant to inlet port of replacement safety valve.
- 6.Position replacement valve at installation point and start mounting hardware.
Range/Stove/Temperature Control Thermostat
appliancepartsprosThe oven thermostat controls the broiler's temperature. If there's a problem with the oven broiler, the thermostat might be broken. This thermostat has a thin copper tube attached to a slightly thicker one that goes into the oven. Inside this tube is a special hydraulic fluid. When the broiler gets hotter, the fluid expands, pushing on a small device in the thermostat and turning the heat off. As the broiler cools down, the pressure lessens and the device lets the broiler heat up again. Testing the oven thermostat is tough, and it can't be fixed if it's broken. If the thermostat is causing the problem, it needs to be replaced.
Repair Steps
- 1.Disconnect power supply - Locate the circuit breaker for the oven and switch it off before starting work. This prevents electric shock.
- 2.Remove control knobs - The knobs on the stovetop need to be removed to access the thermostat. Gently pull them straight off the stems.
- 3.Take off backguard - Unscrew any screws or brackets on the backguard and remove it to access the rear of the thermostat.
- 4.Disconnect wiring - Identify each thermostat wire connection and remove them. Tape wires to keep organized for reassembly.
- 5.Unmount old thermostat - Remove mounting screws to detach the old thermostat from the oven. Be careful not to lose any parts.
Range/Stove/Relay Board
appliancepartsprosSome ovens have a part called a relay board. This board has multiple relays, which manage the electric current going to the heating element. If one or more of the relays on the board fail, the oven won't heat up. If the relay board is faulty, it needs to be replaced.
Repair Steps
- 1.Disconnect power to the oven at the main circuit breaker for safety.
- 2.Remove oven control knobs, bezels and back panels to access relay board.
- 3.Identify wire harness connectors attached to the original relay board.
- 4.Disconnect wire harness connectors by depressing locking tabs and pulling apart.
- 5.Remove mounting screws or clips securing relay board in the oven cavity.
- 6.Carefully lift out old relay board assembly. Check for fit issues with replacement.
- 7.Position new relay board assembly and start any mounting screws or clips.
Range/Stove/Valve and Pressure Regulator
appliancepartsprosThe valve and pressure regulator could be causing the problem, but this is extremely rare. The valve and pressure regulator are often wrongly blamed for issues. Before you replace these parts, it's a good idea to first check all the parts that usually break down more frequently. How to Replace Range/Stove/Oven Valve and Pressure Regulator
Repair Steps
- 1.Shut off gas supply at the main line behind or under the appliance.
- 2.Disconnect flex gas lines from both valve and regulator by loosening coupling nuts.
- 3.Remove valve and regulator mounting fasteners such as screws or nuts.
- 4.Gently remove old valve and regulator taking care not to scratch surrounding surfaces.
- 5.Apply pipe thread sealant to inlet ports of replacement parts before installing.
- 6.Mount regulator first in original position using fasteners by hand only.
- 7.Attach flex gas lines to valve and regulator hand-tightening fittings.
Incoming Power Problem
appliancepartsprosElectric ovens need 240 volts of alternating current to work, while gas ovens need 120 volts. If an oven doesn't turn on, there might be a problem with the power coming in. To find out if the electrical outlet is giving enough voltage, you can use a multimeter. This tool can test the power coming in at the wall socket.
Loose or Burnt Wire Connection
appliancepartsprosOne of the wires that provides electricity to the oven element or igniter could be burned out. This usually happens close to the heat source. To see if a wire is burned out, take a look at the wires that connect to the element or igniter. If a wire is burned out, it will often look visibly charred or burnt.