Leaking
Most Likely Causes
Washing Machine Drain Pump
Most common causeappliancepartsprosThe drain pump, pumps the water out through the drain hose. When the drain pump is cracked, damaged, or if its bearings wear out, it can cause water to leak. Unfortunately, the drain pump can't be fixed. So, if you notice it's leaking water, the best course of action is to replace it.
Repair Steps
- 1.Unplug washing machine. Locate the plug on the back of the machine and disconnect from power source to prevent electric shock.
Washing Machine Hose
Most common causeappliancepartsprosApart from the fill and drain hoses, other hoses in your washing machine could be the cause of a leak. You will need to examine all the hoses, including those connecting the tub and pump, for any signs of damage or loose connections. If you find any issues, replace the problematic hose as needed.
Repair Steps
- 1.Shut off water. Turn off the water supply valves located where the water hoses attach to the washing machine. This prevents water leaks during the repair.
- 2.Release water pressure. Disconnect the hose from the water inlet and run the washer to drain remaining water from the line.
- 3.Detach hose ends. Use adjustable pliers to detach the worn hose from both the water valve and the washer's water inlet port. You may need to grip the metalfitting.
- 4.Remove old hose. Pull the entire hose free once both ends are detached. Inspect the ports and fittings for any damage that requires repair.
- 5.Install new hose. Attach one end of the replacement hose to the washer's inlet port by hand-tightening the coupling nut. Do not overtighten.
Washing Machine Tub Seal and Bearing Kit
Most common causeappliancepartsprosA torn tub seal can be the culprit behind a washer leak. If the tub seal is indeed leaking, water can seep into the tub bearings, potentially causing them to fail. In this case, it's advisable to replace both the tub seal and the tub bearings. It's important to note that this repair is quite complex and will require disassembling a significant portion of the washing machine. While it may be a more involved task, addressing a leaking tub seal promptly and effectively by replacing both the seal and the bearings is imporatnat to prevent further damage and maintain your washer's proper functioning.
Repair Steps
- 1.Prepare for the replacement: Gather all the necessary tools and equipment before starting the replacement process. You will typically need a wrench, pliers, a screwdriver, and a replacement tub seal and bearing kit that matches your washing machine's make and model. Make sure that the washing machine is unplugged and disconnected from any power source.
- 2.Access the tub seal and bearing: The tub seal and bearing are located inside the washing machine's tub assembly. To access them, you will need to disassemble the washing machine. Refer to the manufacturer's instructions or the washing machine's manual for specific guidance on accessing the tub seal and bearing.
- 3.Remove the outer tub: Begin by removing any components that obstruct access to the outer tub, such as the agitator and any other attachments. Disconnect the hoses and any other connections attached to the tub using a wrench or pliers. Once all connections are detached, carefully lift and remove the outer tub from the washing machine.
Washing Machine Dispenser Drawer
Most common causeappliancepartsprosWhen your washing machine is leaking water, start by making sure the dispenser drawer is not only fully closed but also free of any damage. If you find the drawer is cracked or damaged in any way, it could be the source of the leak.If the drawer is damaged it will need to be replaced.
Repair Steps
- 1.Open access door. Find the door or panel that allows access to the dispenser drawer area, usually located on the upper front of modern washers. Remove any screws.
- 2.Remove old drawer. Grasp the sides of the dispenser drawer and pull firmly straight out from the machine. Wiggle slightly if stuck.
- 3.Clear out debris. Use a vacuum or cloth to clean out any remaining detergent residues from the tracks the old drawer slid within.
- 4.Install new drawer. Place the replacement dispenser drawer into the opening, lining up the sides with the tracks inside the washing machine cabinet.
- 5.Slide drawer closed. Firmly push the new drawer shut all the way so it is flush with the front panel. It should lock into place.
Hose
33.7% of casesamazon_reviewsGasket Seal
15.7% of casesamazon_reviewsPump
10.9% of casesamazon_reviewsValve
9.1% of casesamazon_reviewsFilter
4.5% of casesamazon_reviewsMotor
4% of casesamazon_reviewsBearing
3.6% of casesamazon_reviewsAgitator
2.2% of casesamazon_reviewsWashing Machine Transmission
appliancepartsprosIn a top-load washer, there's a transmission shaft that extends into the inner tub. If the transmission bearing or tub seal is damaged, it could lead to a leak around the motor area. Some washer models only sell these parts as a complete assembly. This means that if you're dealing with a leak problem, you might have to replace the entire transmission assembly to fix it.
Repair Steps
- 1.Unplug machine and open panels. Disconnect power and remove rear/bottom access panels for protected internal access.
- 2.Detach transmission belt. Remove belt from motor pulley and any transmission pulleys it engages.
- 3.Disconnect wiring harnesses. Unplug any electrical plugs connected to transmission controls.
- 4.Loosen mounting hardware. Remove retaining bolts or screws securing transmission to machine frame.
- 5.Extract transmission assembly. Ease transmission from mounts, wiggling side-to-side if stuck. Take care not to damage parts.
- 6.Clean transmission area. Wipe away debris from mounts where new unit will sit using dry cloth.
Washing Machine Door Boot Seal
appliancepartsprosIf water is leaking from the door boot seal, it may be torn or damaged. If the door boot seal is damaged it will need to be replaced. The door boot seal is the rubber gasket that seals the washing machine door, and it prevents water from escaping.
Repair Steps
- 1.Open door. Swing open the washing machine door to access the inner seal. The seal runs along the perimeter edge of the door opening.
- 2.Remove old seal. Prise or pinch the seal away from the door flange where it sits. It may be glued or friction fit into place. Pull all parts of the seal out.
- 3.Clean flange. Wipe away any remaining sticky residue from where the old seal sat using a rag dampened with soap and water. Rinse and dry.
- 4.Inspect door. Check that the door and opening are free of visible defects that could compromise the new seal's fit.
- 5.Install new seal. Press or work the replacement boot seal evenly into the channel all around the door opening flange. It may be tapered.
- 6.Test for gaps. Close and latch the door, running a finger along the seal perimeter to check for any splits or gaps where water could enter.
Washing Machine Tub-to-Pump Hose
appliancepartsprosCheck the tub-to-pump hose for any splits or tears. If you spot any damage on this hose, it will need to be replaced. Avoid the temptation to cut off the damaged part of the hose and stretch it to make it fit the pump. Stretching the hose can strain the rest of it, and it might suddenly burst, causing more problems. Replacing the damaged hose is the safest and most effective way to washer running again.
Repair Steps
- 1.Unplug machine and shut off water. Disconnect power and turn off water source to prevent electric shocks or floods.
- 2.Access hoses. Open/remove access panel and locate hoses connecting washing machine tub to pump & drain.
- 3.Detach hoses. Disconnect and remove old hoses from tub/pump fittings using pliers. Don't lose small washers/gaskets.
- 4.Inspect fittings. Check all fittings for cracks/corrosion that require replacement before installing new hose.
- 5.Install new hose(s). Slide one end of replacement hose onto pump fitting, then other end onto tub port. Push firmly until snug.
- 6.Secure hose ends. Use zip ties or hose clamps to prevent hoses from pulling off fittings during operation.
Washing Machine Boot Seal Retaining Ring
appliancepartsprosThe boot seal retaining ring is responsible for keeping the door boot seal securely in place. If this ring is broken or missing, it can lead to the boot seal getting out of position, which may result in water leaking out through the closed door when the machine is running. To prevent this issue, check the boot seal retaining ring for any damage. If you find any damage on the part it will need to be replaced.
Repair Steps
- 1.Open door. Swing open the washing machine door to access the inner boot seal and retaining ring.
- 2.Remove old ring. Pry underneath the edge of the worn retaining ring to pop it out of the door groove. It may be stiff.
- 3.Clean groove. Use a rag to wipe away any debris from the retaining ring groove that runs around the inside of the door opening.
- 4.Inspect boot seal. Check that the boot seal itself is still pliable and seated properly within the outer flange.
- 5.Insert new ring. Compress the replacement retaining ring slightly if needed to seat it start into the groove around the entire door opening.
- 6.Press into place. Firmly press or tap the ring edge all the way down fully into the groove using a small tool if needed.
Washing Machine Water Inlet Valve
appliancepartsprosThe water inlet valve is responsible for letting water into the tub. If you notice water leaking from the washer during the filling stage, the issue likely lies with the water inlet valve or a hose connected to it, which might be damaged. Check the valve housing for any cracks and examine the hoses connected to it for holes or tears. If you find any issues you will need to replace the damaged parts.
Repair Steps
- 1.Shut off water supply. Turn off the valves where the water lines attach to the washing machine. This prevents flooding during repairs.
- 2.Release water pressure. Run the wash cycle to drain any remaining water trapped in the lines before proceeding.
- 3.Disconnect hoses. Detach the hot and cold water hoses from the valve itself using pliers if necessary.
- 4.Remove mounting hardware. Use a screwdriver to take out any screws or bolts attaching the inlet valve to the machine.
- 5.Extract old valve. Ease the inlet valve out of position once it is fully detached from mountings and water lines.
- 6.Inspect seal rings. If the rubber seal rings inside the valve port are cracked or deteriorated, replace them now.
Washing Machine Fill Hose
appliancepartsprosTo make sure your washing machine operates without any water leaks, examine the hot and cold fill hoses. Check that these hoses are tightly connected to both the water supply valves in your home and the water inlet valve intake ports on your washer. Also, make sure there are no holes or tears in the hoses. It's a good idea to replace these fill hoses every five years, even if they seem to be in good condition.
Repair Steps
- 1.Shut off water supply. Locate the water supply valves under the sink or behind the washer and turn them clockwise to the closed position to shut off the water supply to the washing machine. This prevents water from leaking or flooding as you work.
- 2.Disconnect hoses. Disconnect the old fill hose from both the water supply valve and the water inlet valve on the back of the washing machine. You may need an adjustable wrench to loosen the couplings if they are tight.
- 3.Remove old hose. Gently pull the old fill hose out from its position, guiding it out of the machine. Be careful not to damage any other components as you remove it.
- 4.Install new hose. Insert the new fill hose into position, guiding it carefully into place behind the washer. Connect one end to the water supply valve and the other end to the washing machine's water inlet using the couplings. Hand-tighten the couplings.
- 5.Turn on water and check for leaks. Reopen the water supply valves and turn on the water to the washing machine. Check all connections for any signs of leaks and tighten further if needed. Run the washer through a testing cycle without clothes to confirm proper filling and emptying.
Washing Machine Control Board
appliancepartsprosThe main control board of a washing machine is responsible for powering all the electrical components, including the inlet valve that regulates water flow. If this board malfunctions, it may mistakenly provide power to the inlet valve even when not needed, resulting in leaks. To determine if the control board is faulty, carefully inspect it for signs of burning or damaged parts. You can also use a multimeter and reference the wiring diagram to see if power is going to the valve. If you find power at the water valve when a cycle is not selected, you will need to replace the control board.
Repair Steps
- 1.Unplug the washing machine. Disconnect the power cord before servicing to prevent electric shock.
- 2.Open the control panel. The control board is located behind the control panel on the washer front.
- 3.Label connections. Take note of where each wire and connector is attached to the control board.
- 4.Disconnect wires. Carefully detach all wiring harnesses and connectors from the board.
- 5.Remove mounting screws. Use a screwdriver to remove any screws securing the control board.
- 6.Remove control board. Carefully pull the control board free from the washer once all wires are detached.
Washing Machine Drain Hose
appliancepartsprosA possible reason for leaks in your washing machine is the drain hose. This hose often develops leaks where it connects to the pump at the back of the washer. If the washing machine is placed too close to the wall, the hose might rub against it, causing damage and leaks. Check the drain hose thoroughly for any signs of leakage. If you do find leaks, the best course of action is to replace the hose.
Repair Steps
- 1.Shut off water supply. Turn off the valves where supply hoses attach to prevent flooding.
- 2.Disconnect old hose. Detach the drainage hose from both the outlet port on the pump and the hose exiting the machine.
- 3.Inspect hose clamp. Check the hose clamp is in good condition and replace if needed to securely hold the new hose.
- 4.Attach new hose. Connect one end of the replacement drain hose to the water pump outlet port using the hose clamp.
- 5.Route new hose. Feed the free end of the new drain hose through its exit point from the machine cabinet.
- 6.Connect to standpipe. Secure the other end of the drain hose to the standpipe or drainage pipe where washing water expels.
Washing Machine Dispenser
appliancepartsprosIf your washing machine has a detergent dispenser, it might develop issues that can lead to leaks. One common problem is the buildup of detergent residue, which can clog the dispenser and cause water to leak out. Excessive suds from using too much detergent can also be a culprit behind leaks. A crack in the detergent dispenser itself can also cause leaking. Leaks might occur if a small item, like a handkerchief, gets stuck and blocks the water flow between the dispenser and the drum.
Repair Steps
- 1.Unplug machine. Disconnect the washer from its power source to work safely inside.
- 2.Open access door. Locate and remove any screws holding the dispenser access panel on the top of the machine.
- 3.Disconnect hoses. Detach hoses and wires connecting the existing dispenser to the machine components.
- 4.Remove old unit. Pull the dispenser straight up and out of the machine cabinet once all attachments are freed.
- 5.Clean compartment. Wipe out any residue inside the dispenser cavity before installing the new unit.
- 6.Insert new dispenser. Set the replacement dispenser into position within the cabinet opening.
Wrong type or incorrect amount of detergent
appliancepartsprosIf you have a front-load washer and some newer top load models, it's crucial to use HE (high efficiency) detergent as well as the correct amount. This type of detergent is specially designed to produce fewer suds and is intended for use with the lower water levels commonly used in front-load washers. Front-load washers usually have a small overflow system located at the back of the machine. Excessive suds can lead to issues, as they might escape from this system. To avoid any problems, stick to HE detergent, which helps maintain the appropriate suds levels for your front-load washer.
Washing Machine Tub Seal
appliancepartsprosA torn tub seal can be the culprit behind a washer leak. If the tub seal is indeed leaking, water can seep into the tub bearings, potentially causing them to fail. In this case, it's advisable to replace both the tub seal and the tub bearings. It's important to note that this repair is quite complex and will require disassembling a significant portion of the washing machine. While it may be a more involved task, addressing a leaking tub seal promptly and effectively by replacing both the seal and the bearings is imporatnat to prevent further damage and maintain your washer's proper functioning.
Repair Steps
- 1.Disconnect power by unplugging the washer or switching off the breaker.
- 2.Open the washing machine's access panel to get to the tub seal area.
- 3.Locate the retaining clips or screws holding the old tub seal in place.
- 4.Remove the retaining clips/screws to free the worn seal from the tub.
- 5.Gently pull out the old tub seal once fully unsecured from the machine tub.
- 6.Wipe clean the tub rim area where the new seal will be mounted.