Not draining
Most Likely Causes
Washing Machine Drain Pump
Most common causeappliancepartsprosOccasionally, tiny objects or items of clothing can become trapped in the drain pump. To find out if something is blocking the drain pump, take it out and inspect it for any obstacles. If the drain pump is free from blockages but continues to make noise when draining, it's advisable to replace the drain pump.
Repair Steps
- 1.Unplug washing machine. Locate the plug on the back of the machine and disconnect from power source to prevent electric shock.
Washing Machine Control Board
Most common causeappliancepartsprosThe washing machine control board is responsible for supplying power to the electrical parts of the washer. If there is a problem with the board, it may not be sending power to the drain pump when the washer is draining. You can check the board for any signs of burning or damaged components. Additionally, you can use a multimeter to test if power is reaching the drain pump by referring to the appliance's wiring diagram. If you find that there is no voltage when the washer is in the drain cycle, it probably means that the control board is faulty and needs to be replaced.
Repair Steps
- 1.Unplug the washing machine. Disconnect the power cord before servicing to prevent electric shock.
- 2.Open the control panel. The control board is located behind the control panel on the washer front.
- 3.Label connections. Take note of where each wire and connector is attached to the control board.
- 4.Disconnect wires. Carefully detach all wiring harnesses and connectors from the board.
- 5.Remove mounting screws. Use a screwdriver to remove any screws securing the control board.
Washing Machine Timer
Most common causeappliancepartsprosIn some washing machine models, a timer is used to determine the appropriate timing for supplying voltage to the electrical parts of the washer. If the timer is faulty, it may fail to send power to the drain pump when the washer is draining. To identify this issue, you can examine the timer for any indications of burning or damaged components. You can also use a multimeter to assess if power is reaching the drain pump by referring to the appliance's wiring diagram. If you discover that there is no voltage present when the washer is in the drain cycle, it is probable that the timer is defective and necessitates replacement.
Repair Steps
- 1.Shut off power. Turn off electricity to the washer at the circuit breaker or unplug it before servicing electrical components.
- 2.Remove outer panel. Detach any outer covers or casings blocking access to the timer module inside using a screwdriver.
- 3.Disconnect wires. Note the wire colors and locations before disconnecting all electrical wires from the old timer terminals.
- 4.Remove mounting screws. A few screws typically secure the timer module to the inside of the washer cabinet. Remove them.
- 5.Withdraw old timer. Once fully detached from wires and frame, gently lift out the old timer control module straight away.
Washing Machine Suspension Rod
Most common causeappliancepartsprosIf a top-load washer fails to complete a cycle and also doesn't drain, it's possible that a broken suspension rod is causing the tub to become unbalanced, resulting in improper spinning or agitation. Take a close look at the suspension rods to check for any signs of damage, and if needed, replace them. It is advisable to replace all suspension rods at the same time.
Repair Steps
- 1.Unplug the washing machine from the power source. This ensures the washing machine will not start during the repair.
- 2.Tip the washing machine back. Carefully tip the washing machine back to access the bottom panel. You may need assistance to prevent the machine from tipping over.
- 3.Remove the bottom panel. The bottom panel is usually held in place by screws along the bottom edge. Use a screwdriver to remove the screws and detach the panel.
- 4.Locate the suspension rod. The rod will extend from the washing machine tub to the base. Identify which suspension rod needs replacing.
- 5.Remove the retaining clips. Use pliers to detach the retaining clips or rings holding the suspension rod in place.
Pump
36.7% of casesamazon_reviewsHose
35.7% of casesamazon_reviewsFilter
14% of casesamazon_reviewsMotor
9.7% of casesamazon_reviewsValve
8.2% of casesamazon_reviewsGasket Seal
5.8% of casesamazon_reviewsAgitator
4.8% of casesamazon_reviewsSensor
2.4% of casesamazon_reviewsWashing Machine Lid Switch Assembly
appliancepartsprosThe lid switch assembly plays an important role in preventing the washer from spinning when the lid is open. If the lid switch assembly malfunctions, it can lead to a failure in draining. To check if the lid switch assembly is faulty, you can use a multimeter to test the continuity of the lid switch. If a lid switch does not show continuity, it indicates a defect, and it should be replaced.
Repair Steps
- 1.Unplug the washing machine. Disconnect the machine from the power source. This will prevent electric shock.
- 2.Open the lid. Prop the washing machine lid fully open.
- 3.Locate the switch. The lid switch assembly is on the front panel of the washer. Identify the specific location.
- 4.Remove switch mounting screws. Use a screwdriver to detach any screws securing the switch assembly.
- 5.Disconnect wiring. Carefully disconnect the wiring harness or connectors attached to the switch.
- 6.Remove switch assembly. With the screws and wiring detached, you can now fully remove the lid switch assembly.
Washing Machine Main Control Board
appliancepartsprosThe main control board of a washing machine is responsible for supplying power to most of its electrical components. If this board is faulty, it may fail to send power to the drain pump during the drain cycle. You can examine the board for indications of burning or damaged components. Additionally, by using a multimeter and referring to the appliance's wiring diagram, you can test if power is reaching the drain pump. If you find that there is no voltage present when the washer is in the drain cycle, it is highly likely that the control board is defective and should be replaced.
Repair Steps
- 1.Unplug the washing machine. Disconnect power to prevent electric shock.
- 2.Open control panel. Unscrew the control panel on the washer to access interior.
- 3.Locate control board. The main control board is mounted to the cabinet interior.
- 4.Label wire connections. Note where each wire harness connects to the control board.
- 5.Disconnect wires. Detach all wire harnesses from the terminals on the control board.
- 6.Remove mounting screws. Use a screwdriver to remove screws securing control board.
Washing Machine Water Pump
appliancepartsprosOccasionally, small items or items of clothing may become stuck in the water pump, causing it to be unable to remove water from the tub through the drain hose. To check if there is any blockage in the water pump, you need to remove the pump and inspect it for any obstructions. If the water pump is free from blockages, but you still hear unusual noises during the drain cycle, it is advisable to replace the pump.
Repair Steps
- 1.Shut off water supply. Turn off valves where supply hoses attach to prevent flooding during the repair.
- 2.Disconnect hoses. Use pliers to detach hoses from the pump housing inlet and outlet ports.
- 3.Remove mounting bolts. Access and loosen the bolts or screws securing the pump inside the washer cabinet.
- 4.Withdraw pump housing. Gently rock and lift the water pump housing upwards once mounting bolts are disengaged.
- 5.Inspect impeller. Check that the plastic or rubber impeller inside is not cracked or jammed before installing replacement.
- 6.Put in new pump. Position the replacement pump where the old one sat inside the machine cabinet.
Washing Machine Drain Hose
appliancepartsprosInspect the drain hose for any signs of being kinked, twisted, or bent. If you notice any bending, straighten it to allow proper functioning. Furthermore, it is advisable to detach the drain hose and carefully examine it for any blockages. If there are any obstructions present, please attempt to remove them. If you encounter difficulties in clearing the obstructions, it may be necessary to replace the drain hose altogether.
Repair Steps
- 1.Shut off water supply. Turn off the valves where supply hoses attach to prevent flooding.
- 2.Disconnect old hose. Detach the drainage hose from both the outlet port on the pump and the hose exiting the machine.
- 3.Inspect hose clamp. Check the hose clamp is in good condition and replace if needed to securely hold the new hose.
- 4.Attach new hose. Connect one end of the replacement drain hose to the water pump outlet port using the hose clamp.
- 5.Route new hose. Feed the free end of the new drain hose through its exit point from the machine cabinet.
- 6.Connect to standpipe. Secure the other end of the drain hose to the standpipe or drainage pipe where washing water expels.
Washing Machine Coin Trap
appliancepartsprosCertain washing machines have a coin trap, which helps catch any foreign objects that might enter the drain. It's important to regularly inspect and clean the coin trap to make sure its properly functioning. If debris consistently builds up in the coin trap, it can become blocked and prevent the washer from draining effectively. If you're experiencing drainage issues or if the washer fails to drain correctly, and your particular model includes a coin trap, it's recommended to remove the coin trap and give it a thorough cleaning.
Repair Steps
- 1.Disconnect power. Turn off the breaker or unplug the washer before accessing internal components.
- 2.Remove outer panels. Detach any outer cabinet covers securing them with screws to access the trap inside.
- 3.Locate trap bolts. The coin trap mounts to the machine body and is held by bolts or screws.
- 4.Detach bolts. Use a wrench or screwdriver to remove all hardware retaining the old trap in place.
- 5.Remove trap. Once fully unbolted, grasp and lift out the worn coin trap from its position inside.
- 6.Clean mounting area. Wipe away any debris from the washer body where the new trap will mount.
Washing Machine Door Latch
appliancepartsprosThe door latch is responsible for securely closing the washer door during operation. Once the door is properly shut, the washer can start working. If the washer door is not latched shut, the door switch will prevent the washer from operating. If there's a problem with the door latch, the washer will not spin or drain. The door latch can fail either mechanically or electrically. Check the door latch for any signs of damage. If the latch is damaged or doesn't close correctly, it should be replaced. To check if the door latch has an electrical issue, you can use a multimeter to test the switches on the latch for continuity. If any of the switches lack continuity when activated, it's necessary to replace the switch.
Repair Steps
- 1.Unplug the washing machine. Disconnect power to avoid electric shock.
- 2.Open the door. Prop the door fully open to access the latch assembly.
- 3.Remove inner door panel. Detach the screws or clips to remove the inner door panel, if needed for access.
- 4.Detach latch linkage. Disconnect the latch assembly linkage rods from the door mechanism.
- 5.Remove mounting screws. Use a screwdriver to detach any screws securing the latch to the door frame.
Washing Machine Door Lock
appliancepartsprosThe door lock on the washer is responsible for keeping the door securely closed while it's in use. When the door is closed, the washer can start its operation. If there's a problem with the door lock, the washer door won't close properly. The door lock can have either mechanical or electrical failures. Take a look at the door lock to check for any signs of damage. If the door lock is damaged or doesn't latch correctly, it needs to be replaced. To find out if there's an electrical issue with the door lock, you can use a multimeter to test each of the door lock switches for continuity. This will help determine if the door lock has failed electronically.
Repair Steps
- 1.Shut off power. Unplug the washing machine from the electrical outlet or turn off the power at the circuit breaker to ensure the machine won't accidentally turn on during repairs.
- 2.Remove outer cover. Use a Phillips head screwdriver to remove any screws securing the outer plastic or metal cover. Lift it off to access the inner components.
- 3.Disconnect old lock. Locate the door lock assembly, usually on the bottom left or right side of the tub opening. Unplug any electrical connections and unwind wire clips or ties holding the wires in place.
- 4.Unfasten lock bolts. Use your screwdriver to remove any mounting bolts, screws or clips attaching the old lock to the washing machine frame. Lift it out once it's fully detached.
- 5.
Washing Machine Water Pump Belt
appliancepartsprosSome older washing machined have a water pump belt. If this belt becomes broken or worn out, the washer will be unable to drain properly. Take a moment to inspect the belt and replace it if you notice any indications of significant wear.
Repair Steps
- 1.Shut off water supply. Turn off valves where supply hoses connect to prevent flooding during repairs.
- 2.Disconnect hoses. Detach hoses from pump housing to access belt inside. Use pliers if needed.
- 3.Loosen retaining bolts. The water pump is usually secured inside the machine cabinet. Loosen bolts.
- 4.Tip out water pump. Gently rock or rotate the pump housing until it comes free from loosened bolts and can be lifted out.
- 5.Release belt tension. A bolt or lever typically tensions the belt around the pulleys. Loosen it.
- 6.Remove old belt. Slide the worn belt off one pulley, then the other to remove it fully from the pump compartment.
- 7.
Clogged Pump or Hose
appliancepartsprosIt's possible that foreign objects like lint, coins, or safety pins could have ended up in the pump of your washing machine. To prevent these items from reaching the pump impeller, most front-load washers are equipped with a clean-out feature. If your machine has a clean-out, it's important to check it for any potential obstructions.
Drain hose is clogged or kinked
appliancepartsprosTake a moment to inspect the drain hose for any kinks or clogs. If your washer tends to move or "dance" while running, it could have shifted and caused the hose to bend. Another possibility is that the drain hose might be clogged with lint or hair. To address this, you can use a slender brush with a long handle to clean out the hose.
Door lock or door latch obstructed
appliancepartsprosRemove any debris that may be present in the door lock or latch assembly. The presence of debris in these areas can hinder the proper functioning of the washer.
Obstructed Lid switch assembly or Door lock
appliancepartsprosIt is important to remove any debris that may be present in the door lock or lid switch assembly. The presence of debris in these areas can hinder the unit's performance.